You are not logged in.

Dear visitor, welcome to Xtrend Support / GigaBlue Info. If this is your first visit here, please read the Help. It explains in detail how this page works. To use all features of this page, you should consider registering. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.


Saturday, October 10th 2015, 7:32pm

how can i jtag et9000 ?

please help me

When I flash bootloader electricity was suddenly cut off.
Now, only a few flashes and then turns et9000 is dead
usb not work.
How i can flash boot loader with jtag ?


Sunday, October 11th 2015, 10:26am

I have never seen a description for that for Xtrend boxes.
If you attach rs232 cable do you see output? If yes, try to access cfe console by pressing ctrl+c several times right after boot. In cfe console you can try to flash bootloader.


Sunday, October 11th 2015, 11:15am

If you have the necessary programming enviroment for Broadcom-CPUs and and the according JTAG adpater, it will be possible to access the BCM7413. Then you need the exact register configuration, the correct DRAM Setup and the NOR Flash programming utillity. If you have reached that point, you can start to recover your Xtrend again. As these information are very hard to get, except you work in the direct setup and service of these Xtrend boxes, it is much easier to unsolder the NOR flash and program it in a TSSOP socket via a conventional programmer.

Murphy-09 ;)

This post has been edited 2 times, last edit by "Murphy-09" (Oct 11th 2015, 11:38am)



Posts: 3,696

Location: Europa

  • Send private message


Sunday, October 11th 2015, 11:24am

When I flash bootloader electricity was suddenly cut off.
Now, only a few flashes and then turns et9000 is dead

like betacentauri said, try to connect to CFE, then it is maybe possible to flash...
or take the hard way like Murpy-09 told us.

Are you sure, that power supply was not broken before you tried to flash?

Ihr Xtrend Support-Team
eXtrending your vision


Sunday, October 11th 2015, 1:50pm

Thank you friends
power supply is ok cheked out voltae.
et9000 was ok when i falashhng with usb electricity was suddenly cut off
rs232 not work .usb not not work .

the receiver (et9000) has the ability Jtag ?
I know a little electronics.
These are the things I need.
1-Map build cables. 2-jtag place. 3-The application for communication with receivers


Sunday, October 11th 2015, 2:52pm

As said nobody knows the details and has the software. I fear you have to send the receiver back to manufacturer.


Sunday, October 11th 2015, 3:50pm

If you send me the MAC address of your receiver, I can send you the complete NOR Flash Image as binary will be 4MBytes long....

Murphy-09 ;)


Sunday, October 11th 2015, 4:39pm

I live in Iran. Receivers use is prohibited.
I can not send to the factory.


Sunday, October 11th 2015, 4:41pm

mac address is 00:16:b4:03:9b:be


Sunday, October 11th 2015, 5:10pm

here is the binary contents of your NOR flash with the MAC address 00:16:b4:03:9b:be

Murphy-09 ;)
Murphy-09 has attached the following file:


Sunday, October 11th 2015, 5:15pm

thank you my dear
How do I transfer this files to the receiver?


Sunday, October 11th 2015, 5:26pm

This binary Image can be used witin a normal flash programmer, if you desolder your NOR Flash from the main board, or better, if you program a new one and replace it against the old one.
If you have the necessary JTAG enviroment from ABATRON or LAUTERBACH, you might be able to reprogram the NOR Flash within the System.....
As I don't have any configuration files, I've got no chance with the JTAG feature, so I usually unsolder the NOR in such cases, which worked upto now a several times.

Murphy-09 ;)


Sunday, October 11th 2015, 10:32pm


maybe a E3-flasher will work?


Monday, October 12th 2015, 3:18am

Thank you, dear friends.
I am amateur.
I do not have any device programmer.
Where motherboard's jtag cable connect or solder?


Monday, October 12th 2015, 10:16am

i think jtag cable is to solder.

also some reciever has only jtag solderpoints so you have to solder in pins first
(i know these from some comag stb´s)

if it is possible with e3 flasher or something similar to use clips only on NOR, i would prefer this method.
(e3 flasher is for downgrading PS3 with NOR).


Monday, October 12th 2015, 11:28am

this is motherboard's et9000
usb and rs232 and network not work.
Where this motherboard solder jtag cable should I do?
morteza-m has attached the following file:
  • et9000.JPG (2.69 MB - 89 times downloaded - latest: Feb 25th 2020, 8:01am)


Monday, October 12th 2015, 1:49pm


Before going into JTAG operation, have you already replaced the capacitors in your ET-9000? All owners of ET-9000 (includind mines) need to replace the capacitors after a while.
Since you mentionned that your USB gets no more power you should carefully check the capacitors and replace the potentially defective ones.

Then try to start again a new USB flash.



Monday, October 12th 2015, 8:20pm

don´t know where to solder jtag there...

but in the center above the heatsink is the NOR Chip.
looks like an E3Clip will fit, and direkt flash will work...

This would be the safest way i think.


Tuesday, October 13th 2015, 9:27am

Thank you, dear friends

Receivers quite was healthy. When USB flashing suddenly lost power (Electric City)
I do not have any connection with the receiver's just jtag (usb-rs232-network not work)

help. How can I jtag ?
Where is the location of the solder on the motherboard ?
Excuse me. My English is not good.


Tuesday, October 13th 2015, 4:00pm


This is the socket?
is it jtag??
morteza-m has attached the following file:
  • et9000.JPG (2.95 MB - 86 times downloaded - latest: Feb 25th 2020, 8:03am)

Similar threads